Buying and fitment • Updated October 27, 2026

SCX30 Tacoma upgrades: links, wheels and fitment

Get the 107mm wheelbase, link lengths and T1/T2 wheel-clearance checks right before choosing parts.

Based on manufacturer specifications and seller fitment details.

SCX30 Tacoma wheelbase: 107mm, not 99mm

The Tacoma uses a 107mm wheelbase. Axial specifies its AXI-3307 link set for the 99mm Bronco, K10 and Wrangler JLU, and AXI-4429 for the longer Tacoma. Wheelbase is the distance between front and rear axle centers; “107mm links” describes the vehicle application, not the length of each link.

Axial-listed suspension link lengths (mm)
Link position99mm SCX30: AXI-3307107mm Tacoma: AXI-4429
Front upper3032.5
Front lower35.538.5
Rear upper40.546.5
Rear lower45.2551.25

Sources: Axial AXI-3307 and Axial AXI-4429. These are the manufacturer's listed part lengths, not measurements taken by Crawlers Bot.

Both front and rear links differ. Treating a 99mm-to-107mm conversion as a rear-link swap misses the front geometry. Check shaft travel through compression and droop, axle position under the body, steering movement and chassis mounting points before running a conversion.

For a 99mm rig, compare the AXI-3307 set instead. An aftermarket listing that only says “SCX30” needs a wheelbase check.

Tacoma T1 and T2: why tire clearance differs

Axial's green T1 crawler has deleted fenders, wider-offset KMC Torx wheels and larger BFGoodrich Krawler tires. The T2 overland version has fender flares, a narrower stance, Black Rhino Bahari wheels and Yokohama Geolandar X-MT tires, plus roof-rack details. These are different wheel/body packages, not just colors. See Axial's Tacoma specifications.

A tire that clears a T1 may contact a T2 fender. Record your model suffix and any axle or wheel changes before asking a seller about fitment. Test with the body installed, steering at full lock and one side of the suspension compressed; a straight-ahead bench photo cannot show every clearance problem.

SCX30 wheel size and stock tire size: what to measure

Separate three dimensions: the wheel's nominal tire-mounting size, the wheel's outer diameter and the tire's outer diameter. They are not interchangeable. For example, MEUS lists its SCX30 beadlock wheels as 0.7-inch, with a 21mm outer diameter and 10.5mm width. Those dimensions describe that aftermarket wheel, not the Tacoma's stock tire.

There is no single stock Tacoma tire size to assume across T1 and T2. The Axial product page distinguishes their tires but does not give us a verified numeric outside diameter for both versions. Measure your installed tire across the tread without compressing it, then measure width. Keep that baseline when comparing a replacement; do not substitute a generic SCX30 tire measurement.

  • Match the tire bead to the wheel and confirm the wheel's axle mounting interface.
  • Compare wheel offset, backspacing and hub engagement, especially after an axle swap.
  • Check clearance at the steering links, knuckles, shocks and body through the full movement range.
  • Use the tire maker's outside diameter and width, not only “0.7-inch,” when judging a larger tire.

For a concrete wheel option, inspect the MEUS SCX30 0.7-inch beadlock listing, then apply those checks to your Tacoma variant. Its SCX30 fitment label does not certify every tire/body combination.

Which SCX30 Tacoma upgrade should come first?

Choose a change for a repeatable problem on the terrain you drive. Run the same obstacle before and after, changing one thing at a time.

  1. Repair a fault before tuning around it. Binding, a damaged shaft or a loose wheel can look like a performance limitation. Match replacement links and shafts to the wheelbase above.
  2. For poor grip, inspect tires and clearance first. A larger tire may add clearance under the axle but also rub the body. A rubbing tire or an unsuitable insert can defeat the intended benefit.
  3. For suspension changes, check the entire travel range. Longer shocks can alter ride height and shaft angles. Check that shafts neither bottom out at compression nor separate at droop before driving.
  4. For axle or drivetrain changes, identify the exact assembly. MEUS's three-section CVD shafts are replacements for its Isokinetic axle, not proof of a drop-in fit for a stock Axial housing.

A chassis conversion needs a parts list for motor/transmission mounting, links, shafts, body mounts and electronics. Keep those costs together when deciding whether a conversion solves your problem. For the broader decision process, read how to choose your first crawler upgrades.

Fix the stock fault before choosing a conversion

A link that has popped off, a shaft that separates at droop and a tire that catches the body need different fixes. Disconnect the battery before inspecting the truck. Look for a missing fastener, displaced joint or contact mark first. Refit a sound part according to the manual; replace a cracked or worn component with its specified application. A more expensive material does not correct the wrong length.

For damaged Tacoma suspension links, compare the accepted AXI-4429 link and servo-horn set. For its long-wheelbase shafts, use the AXI-4428 driveshaft listing. Axial identifies both for the 107mm Tacoma application. The AXI-3307 set is the 99mm reference discussed above. Use the manufacturer's application and part number if a catalog field conflicts with them. Sources: Axial links, Tacoma shafts, 99mm links.

After repair, check the movement that exposed the problem: full steering lock, suspension compression and droop, with the body installed. If the same fault remains, stop and identify the contact or assembly problem before adding weight or power. Keep the original working configuration available while evaluating a conversion.

Price the complete change, including the parts you keep

Use three lines in your parts notes: what stays, what changes and what remains unverified. A wheel change needs a compatible tire bead and axle interface; a motor conversion also needs mounting space, a suitable ESC and a plan for the existing receiver and wiring. A servo's advertised torque does not settle its mounting, horn or electrical fit.

Before buying, ask the maker about your exact wheelbase, Tacoma body package and current axle assembly. Then compare the same manufacturer ID across seller offers, including hardware and shipping. A lower price on a similarly named 99mm part is not a saving for a stock Tacoma repair.

Record the measurements and source link in the interactive fitment worksheet. It keeps a draft in this browser, downloads a PDF, and exports an editable backup that you can reopen on another device. Worksheet answers are not submitted to the server or added to analytics events. Keep a backup before clearing browser storage; the worksheet records your checks but does not certify fitment.

Continue with Tacoma-specific listings or the SCX30 family. Use tires and inserts only after deciding whether grip, clearance or a damaged component is the actual problem.

SCX30 Tacoma compatibility questions

Will a 99mm SCX30 link set fit the Tacoma?

It is not the specified stock replacement. The Tacoma's 107mm application uses AXI-4429; both front and rear link lengths differ from AXI-3307. A deliberate wheelbase conversion also needs drivetrain and body checks.

Does “107mm links” mean four 107mm-long links?

No. It refers to the vehicle wheelbase. The Tacoma's four link positions have different listed lengths, shown in the table above.

Can I use SCX24 parts on an SCX30?

Only where the manufacturer identifies the particular part as compatible. Axial specifically mentions SCX24 worm-gear options for ratio tuning on the Tacoma; that does not make SCX24 links, axles, wheels or electronics interchangeable as a family.

Are heavier metal parts always better?

No. Added weight changes the load the motor and steering must move. Decide where you need strength or weight, check the mounting dimensions, and retain the original parts so you can compare the result.

Continue with the right platform and parts

Product pages show the available merchant offers and their current catalog price and stock information. Verify final fitment, price and availability with the seller before ordering. This guide does not freeze a price or claim an item is in stock.